Cook CCP User Manual download pdf

Figure 2 - Non-ducted Inlet Clearance

Storage

If the fan is stored for any length of time prior to installa-

tion, completely fill the bearings with grease or moisture-

inhibiting oil (refer to Lubricants on page 5). Rotate the

wheel several revolutions every three to five days to keep a

coating of grease on all internal bearing parts.

Store the fan in its original crate and protect it from dust,

debris and the weather.

Outdoor Storage

To maintain good working condition of the fan when it is

stored outdoors, follow the additional instructions below.

• Coat the shaft with grease or a rust preventative com-

pound.

• Wrap bearings for weather protection.

• Cover the inlet and outlet to prevent the accumulation of

dirt and moisture in the housing.

• Periodically rotate the wheel and operate dampers (if

supplied).

• Periodically inspect the unit to prevent damaging condi-

tions.

Installation

When mounting the fan, be sure that the structure of the

wall is rigid enough to support the weight of the fan and its

motor.

Consult the specific fan type submittal for the exact fan

dimensions needed to determine the size of your wall open-

ing. The wall opening should be just large enough for the

Centrifugal Plug Fans

INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

CCP

This publication contains the installation, operation and

maintenance instructions for standard units of the CCP

Centrifugal Plug Fans.

Carefully read this publication and any

supplemental documents prior to any

installation or maintenance procedure.

Loren Cook catalog CCP provides additional information

describing the equipment, fan performance, available

accessories, and specification data.

For additional safety information, refer to AMCA publica-

tion 410-96, Safety Practices for Users and Installers of

Industrial and Commercial Fans.

All of the publications listed above can be obtained from

Loren Cook Company by phoning 417/869-6474, extension

166; by FAX at 417/832-9431; or by e-mail at info@loren-

cook.com.

For information on special equipment, contact Loren

Cook Company Customer Service Department at 417/869-

6474.

Receiving and Inspection

Carefully inspect the fan and accessories for any dam-

age and shortage immediately upon receipt of the fan.

• Turn the wheel by hand to ensure it turns freely and

does not bind.

• Inspect dampers (if supplied) for free operation of all

moving parts.

• Record on the Delivery Receipt any visible sign of

damage.

Handling

Lift the fan by the base or lifting eyes on the housing.

NOTICE! Never lift by the shaft, wheel, or motor.

Rotating Parts & Electrical Shock Hazard:

Disconnect electric power before working on unit.

Follow proper lockout / tagout procedures to ensure

the unit cannot be energized while being installed or

serviced.

A disconnect switch should be placed near the fan in

order that the power can be swiftly cut off, in case of

an emergency and in order that maintenance

personnel are provided complete control of the power

source.

Grounding is required. All field-installed wiring must

be completed by qualified personnel. All field-

installed wiring must comply with National Electric

Code (NFPA 70) and all applicable local codes.

Failure to follow these instructions could result in

death or serious injury.

CCP

1 2 3 4 5 6 7 8

Summary of Contents

Page 1

Figure 2 - Non-ducted Inlet ClearanceStorageIf the fan is stored for any length of time prior to installa-tion, completely fill the bearings with grea

Page 2 - Inclined

2115 and 230 Single Phase MotorsFan wheel rotation is set correctly at the factory. Chang-ing the rotation of this type of motor should only be attemp

Page 3 - Delta-Connection

3Wiring DiagramsFanMotorDamperMotor*SecondDamperMotorTransformer**Transformer**L3L2L1Ground AGround BT-1T-4Low SpeedHigh SpeedL1L2LineGround BJ-10T-5G

Page 4 - Tolerance

4Final Installation Stepsa. Inspect fasteners and setscrews, particularly fan mounting and bearing fasteners, and tighten accord-ing to the recommende

Page 5 - Maximum RPM

5 Motors are provided with a polyurea mineral oil NGLI #2 grease. All additions to the motor bearings are to be with a compatable grease such as Exxon

Page 6 - Troubleshooting

6torque chart.o. Turn the shaft by hand. Resistance should be the same as it was before hold-down bolts were fully tight-ened.p. Tighten bearing setsc

Page 7

7CCP Parts ListPartNo.DescriptionSizes 120 - 4451 Fan Sheave2 Belt Set3 Motor Sheave4 Motor5 Motor Plate6 Mounting Plate7 Shaft8 Insulated Plug (Optio

Page 8 - CCP IOM - Dec 2013

8Corporate Offices: 2015 E. Dale Street Springfield, MO 65803 417.869.6474lorencook.comCCP IOM - Dec 2013Limited WarrantyLoren Cook Company warrant

Comments to this Manuals

No comments

Cook CCP User Manual

Browse online or download User Manual for Kitchen Cook CCP. COOK CCP User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Kitchen Cook CCP